Pages

Thursday 28 April 2016

WSPR Transmitter

So after testing I was excited at how well the 20m WSPR transmitter my son soldered up for me worked. It performed flawlessly on the bench with a power output of 0.5W, just as intended. If it hadn't been such inclement weather this week it would have been on air by now. Hopefully if fines up in a few days so we can hoist up a dedicated antenna for this.

I have attached some shots of the top and bottom PCB layers. Pushing stuff around so the silkscreen would be legible took a lot longer than I expected. But it is almost done now and I will route the board again soon and get some fabricated in China.


Naturally I'm pretty chuffed about how well this project has come along. If you'd like to emulate it please let me know.

Regards
Richard VK6TT

Sunday 24 April 2016

WSPR Transmitter

It was an interesting week. I had my 11yo son put together my second prototype WSPR transmitter. Watching someone build this was both instructive and rewarding. I saw first hand how important it was for consistency in labelling parts on the circuit diagram and parts placement diagram.  And rewarding to see that one of your creations can be replicated.

I lost a lot of time testing the synthesiser though. It took me several attempts before I realised the reason the phase lock loop (PLL) was not locking up was not related to the loop filter which I thought was the issue. Instead, it was the oscillator was too low level for the PLL counters to work properly all the time.

As the frequency changed the oscillator level also changed. And it turns out the levels were right on the limit for reliable counting. So it would appear to be working properly when the frequency into the PLL was too low, but as the frequency increased it started counting in error so the error signal into the loop filter was still saying the oscillator was too low.

All is good now though. After some more testing I should be in a position to release further details shortly.

73's
Richard

Thursday 14 April 2016

ESR Meter for Testing Capacitors

Update: Schematic showing parts values available on request.

I always had a feeling I should have an ESR meter but the high cost of commercial kits kept putting me off. I wanted something that was more than a go / no-go indication. However, I didn't want a digital display. As time passed I tucked away some of the circuits I came across.

One day, when looking at some air conditioning controller boards I had been given, I noticed an IC marked LMV324. Turns out this is a 3V single supply version of the LM324. Since I had recovered several of these, and faced with a task where an ESR meter might be useful, I set about amalgamating some ideas I had seen.

The result was a resounding success. I could discriminate between shorts, 1 ohm and 0.33 ohm resistors with ease. Testing on capacitors showed that for the same value and type of capacitors I could easily detect which of a group had a higher ESR. This was true whether the capacitors were in circuit or not.





Here is a brief overview of how it works. The IC contains four op-amps. One op-amp is configured as an oscillator around 50-100kHz. After buffering by another op-amp, the heavily attenuated waveform is applied to the capacitor under test. The capacitor is in parallel with 5 ohms of resistance. The third op-amp, used as a differential amplifier, amplifies the difference in voltage between:
  • the parallel resistance of the 5 ohms of resistance and the capacitor under test versus
  • a second resistor string of just 5 ohms.

 So, the better, or lower, the ESR of the capacitor at the oscillation frequency the greater the output of the differential amplifier stage. Finally, a precision rectifier stage is used to drive the meter.

There is minimal meter deflection when no capacitor is being tested so the coin cell lasts for ages. When I'm finished using the meter I pop the battery out and reinsert into the holder upside down for storage.

I was going to make up a table to calibrate the meter but I never got to it. It was just so intuitive in use that it seemed unnecessary.